What does OL mean on my washing machine

If OL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer.

Why does my washer keep saying OL?

First, OL stands for “Overload”, so in other words, the washer thinks the tub is too hard to move because it’s overloaded and the motor is struggling or the unit is way out of balance causing the washer to struggle. The most common problem is a nut below the inner tub that needs to “float”.

How do I reset my Whirlpool Cabrio washer?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

How do I reset my washing machine motor?

Unplug the washer for 1 minute from the electrical outlet.
Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
The motor has now been reset and is ready for you to start a cycle.

What does OL mean on Kenmore Elite washer?

The OL code means an overload has been detected by the main control. Worse case scenario is the overload error is being triggered by a bearing in the outer tub. The bearing may be causing extra drag that the control interprets as being caused by an overloaded washer.

Why does my Whirlpool Cabrio keeps saying uL?

If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.

How do you fix the UL code on a Maytag washer?

UL is the code for unbalanced load. Open the lid and redistribute your wash to balance the weight of the wet items, then restart the machine. Repeat until the washer spins without thumping.

What does F70 mean on a Maytag washer?

The F70 error code indicates a communication failure between the control boards. Something like this is usually caused by a loose harness or defective control. 1. Unplug the washer for 5 seconds and then wait another 30 seconds after you plug it back in order to re-sync the Machine Control to the UI.

What is the F70 code on Whirlpool washer?

The F70 error on this model washer is a central control unit (CCU) heartbeat failure. This means there is communication loss from the central control unit and the user interface. … If all the wiring and connections look good and the drum on the washer rotates replace the user interface.

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

Article first time published on

What causes a washing machine not to drain and spin?

If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

What are common problems with washing machines?

It Bounces Around. …
It’s Noisy. …
Clothes Are Getting Ripped. …
Improper Or Slow Draining. …
My Washing Machine Won’t Spin. …
There’s No Water. …
The Door Won’t Open. …
It’s Smelly.

What does OL mean on a Whirlpool Cabrio washer?

The OL error code indicates that the washer is overloaded. If the washer is not overloaded, this would indicate either a drag on the drive system or the control board is failing. Be sure nothing is on the floor under the washer that could be causing a problem.

What does Ld mean on a Whirlpool Cabrio washer?

If Ld (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water.

How do you reset a Kenmore Elite washer?

Press the “Stop” button twice, and then press the “Power” button. Video of the Day.
Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
Press the “Start” button to complete the reset process and restart the washing machine.

How do I run diagnostics on my Kenmore Elite washer?

With the washer empty, close the door.
Push “control/on” or “Start”
Select “Drain/Spin”
Select “No Spin” by pressing SPIN SPEED touchpad.
Push “PREWASH” option four times within 5 seconds. (If there is no PREWASH option, press RINSE HOLD 4 times in 5 seconds.)
C:00 should light up and begin the diagnostic.

How do you reset a Kenmore Elite Oasis washer?

The only way to reset a washer, is to disconnect it from the outlet or switch off the designated home circuit breaker for 20-30 minutes, then restore the power.

What does OL mean on a Maytag washer?

Is the Washer overloaded? If OL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent.

What does OFb mean on Maytag washer?

Your washer is off balance. If OFb (off balance load) appears in display, the load is out of balance. The washer was unable to remedy the off balance load via automated methods and now needs manual intervention to redistribute the load evenly around the washplate.

How do you reset a Whirlpool washing machine?

Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.

What does F70 mean?

Posted: 09/01/14. Doug, F70 means check harness connections at the machine control and at the console electronics. If your connections are fine to the machine control board and the console electronics, then you may need to change the machine control board.

What does F 70 mean on a Whirlpool dryer?

The F70 error code on a Whirlpool dryer means the User Interface Board and the Main Control Board have stopped communicating with each other. Firstly, reset the dryer by shutting off the power supply and turning it back on a minute later.

What does F70 mean on a Whirlpool Duet dryer?

Typically the F70 error indicates a communication error between the touchpanel /console controls and the main control board. Whether that’s because there’s an issue with one board or the other (sometimes both if there are updates), loose terminals, in extreme cases there might be an issue with the wiring harness.

What does F70 mean on a Kenmore washer?

The “F70” fault code implies a loss of communication between the Central Control Unit (CCU) and the User Interface. The wire connections between the User interface and the Central Control Unit (CCU) will need to be checked. The User Interface and Central Control Unit are accessed by removing the top.

What does F71 mean on a Whirlpool washer?

The Whirlpool Duet Washer F71 Error is a user interface heartbeat failure. It means the central control unit (CCU) is not detecting input from the user interface boards. Check the wiring between the user interface control boards and the central control unit for loose connections or damaged wiring.

What is F70 code on Kenmore washer?

The F70 error code is a heart beat error in the main control board. To determine the cause of the problem you will need to unplug the washer for 30 seconds then plug the washer back in. … If the washer will not power up, unplug the washer again and access the motor control board.

How do I know if my washing machine motor is bad?

Set the multimeter on the lowest setting, or RX1. Touch a probe to a metal tab. You should get a 0 reading or a number near 0. An infinite reading indicates a failed motor.

How do I know if my washing machine control board is bad?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.

How many years should a washing machine last?

How long does a washing machine last? A typical washer should last 10-13 years. Top-loading washers typically last a few years longer than their front-loading brethren. If you use a stacked washer/dryer combo, you may have to replace both if one starts acting up.

Is it worth it to repair a washing machine?

Repair: If the repair would cost less than 50% of the price of a new appliance and your machine still has several expected years of life left, a quick fix could be a cost-effective solution over replacing the entire washer. An active warranty can also make any repair worthwhile.

Why has my washing machine stopped working mid cycle?

If a washer stops mid-cycle, it could be because the pump or the motor that runs it has failed. When this happens, it cannot remove the water efficiently, pump water in, and thus the sensors won’t allow it to move to the next cycle.